Lattice Felting Technique

See FibreArtsy.com for full article and many other useful tips.

Lattice Felting is just like the name suggests, it’s a wet felting technique which produces a fabric with holes in it. There are a few different ways to achieve this. I’m going to show you how to lay out the fibre to produce the holes.

Step 1: Supplies Needed:

Wool Roving

Silk Sliver (optional) I import silk slivers from Rajasthan and can supply them in a range of colours starting at £5.

Matchstick Blind or Bubble wrap

Hot water

Olive oil soap or liquid fabric soap.

Plastic bottle with holes in cap

Plastic tablecloth or sheeting.

Extra piece of plastic or bubble wrap.

Step 2: Lay Out the Fibre

Cover your table with plastic and lay down the blind or bubble wrap. If using bubble wrap, make sure your pieces are larger than the final scarf. Begin by drafting or thinning out your roving. I’m using merino wool which comes in a pretty thick roving so it needs to be drafted. Take a piece of roving and firmly hold it with one hand. With your other hand, take a hold of the roving about 12″ away and gently pull to thin it out. This takes a bit of practice to get it even. If it breaks, no biggie, just overlap the ends. Lay down your drafted lengths in one direction. I used 5 lengths about 8 feet long.

Once you have finished placing the first layer of strips, add some silk, if using. I like to add silk to my pieces to give them more dimension, texture and luster. It’s completely optional!

Add Layer 2
Again, draft your strips of roving and then lay them in the opposite direction, creating a lattice pattern. The lines don’t have to be straight and can overlap each other and the edges for a more artsy look. Again, add bits of silk.

Step 3: Sprinkle With Water

Now, you are ready to begin the felting process. Fill your bottle with very warm water and add a couple squirts of soap. Sprinkle the fibre thoroughly. Lay a piece of plastic or bubble wrap over a section of fibre and begin rubbing the surface with your hands to work the water into the fibre. You want to make sure that the roving is completely saturated (dry fibre won’t felt). Add more water, if necessary. Do this to all of the fibre, again, making sure it is completely wet.

At this point you can also adjust the edges where needed. Some of the holes in the lattice work may have been closed up by fibre. Gently, move the fibre back in place.

Step 4: Rolling

Beginning at one end, tightly roll up the blind or bubble wrap. Using yarn or nylon hose, tie your roll in 2 or 3 places to secure. Now, lay your hands on the blind and begin rolling it back and forth, from your hands to your elbow and back again. Do this about 200 times. Arms getting tired yet? Slowly and carefully, unroll the piece, re-wet your fibre and roll it up from the opposite end. Again, secure with string and roll it back and forth another 200 or so times.

Step 5: ​Pinch Test

At this point, the fibre should be felting well and holding together. Carefully, unroll your piece and do a pinch test. With your thumb and forefinger, pinch a bit of fiber and gently pull up. Is it holding together? If yes, move on to the next step. If no, continue rolling.

Step 6: ​Throwing

Next step….throwing! This will full your fiber, meaning it will shrink and complete the felting process. Don’t start throwing until your piece has passed the pinch test! Make sure all of the fiber is holding together, especially the joints where the pieces intersect. Pick up your scarf GENTLY, wad it up and let it fall on the table. No force here, just gently let it drop. Pick it up and drop it again. Do this about 50 to 100 times. After a while, you’ll notice the fibers firming up so you can increase pressure. Now, carefully lay it out and pull apart any areas that are not supposed to be sticking together. Continue throwing your scarf until it firms up. The longer you throw it, the more the felt will harden and shrink. Once it’s all holding together, how long you throw it and how much you shrink it, is up to you.

Step 7: ​Finishing

All that’s left now is to thoroughly rinse all the soap out of your scarf. Hang up to dry.

We have a be nice policy.
Be positive and constructive.

Sitemap | TOS | Privacy Statement | Privacy settings | Legal

Autodesk

© 2020 

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.